JBC Preheaters

PHNE is a complete solution for refinishing small printed circuit boards, such as those commonly used in smartphones. It has a heating surface of 108 x 70 mm. It is highly reliable and unmatched in temperature accuracy and PCBA control so no component is damaged.

It has three operating modes:

• Power Mode enables operation at a fixed power level with the possibility of using a protective thermocouple
• Temperature mode maintains the PCBA at a selected temperature, using a control thermocouple and, optionally, protection thermocouples
• The profile mode allows control of the PCBA heating rate using a control and protection thermocouple, without exceeding the recommended limit levels in each application. It has 22 customizable profiles

Two thermocouples can be connected in any of three modes.

PHSE is a complete solution for finishing small and medium PCBAs. It has a heating surface of 130 x 135 mm and four TC connections. It is highly reliable and unmatched in temperature accuracy and PCBA control so no component is damaged.

It has three operating modes:

• Power Mode mode enables operation at a fixed power level with the possibility of using a protective thermocouple
• Temperature mode maintains the PCBA at a selected temperature, using a control thermocouple and, optionally, protection thermocouples
• The profile mode allows control of the PCBA heating rate using a control and protection thermocouple, without exceeding the recommended limit levels in each application. It has 22 customizable profiles

Up to four thermocouples can be connected in any of the three operating modes.

PHBE is a complete solution for finishing medium and large PCBAs, such as those commonly used in laptops or PCB panels. It has a heating surface of 360 x 277 mm and four TC connections. Highly reliable and unmatched in temperature accuracy and PCBA control so no component is damaged.

It has three operating modes:

• Power Mode mode enables operation at a fixed power level with the possibility of using a protective thermocouple
• Temperature mode maintains the PCBA at a selected temperature, using a control thermocouple and, optionally, protection thermocouples
• The profile mode allows control of the PCBA heating rate using a control and protection thermocouple, without exceeding the recommended limit levels in each application. It has 22 customizable profiles

Up to four thermocouples can be connected in any of the three operating modes.

PHXLE is used for preheating large PCBAs such as communication boards, boards used in the aircraft industry, etc. and is ideal for repetitive soldering jobs. It has a heating surface of 510 x 610 mm, with 6 independent working zones (255 x 203 mm) that can be switched on/off. It is highly reliable and unmatched in temperature accuracy and PCBA control, so no component is damaged.

It has three operating modes:

• Power Mode mode enables operation at a fixed power level with the possibility of using a protective thermocouple.
• Temperature mode maintains the PCBA at a selected temperature, using a control thermocouple and, optionally, protection thermocouples.
• The profile mode allows control of the PCBA heating rate using a control and protection thermocouple, without exceeding the recommended limit levels in each application. It has 22 customizable profiles.

Up to eight thermocouples can be connected, allowing the operator to operate in any of three operating modes.

PHNE Preheater for printed circuit boards up to 108x70mm

• Maximum power – 300 W
• Adjustable temperature – 50 to 250 ºC / 120 to 482 ºF
• Heating surface – 108 x 70 mm
• Type K TC connector – 2 for control and protection
• Profiles – 20 (up to 6 steps for each)
• Setting temperature profiles – 3 profiles (2, 3 or 4 steps)
• Maximum working time – 50 min or unlimited
• ESD Safe – Supports ANSI/ESD S20.20-2021
• USB-A – Update firmware, graphics and profiles
• USB-B – PC communications
• Robot connector – Remote control
• Aux. connector – Connection to the console
• Pedal connector – Pedal connection (P-005) for heater control

PHSE Preheater for 130x130mm printed circuit boards

• Maximum power – 800 W
• Adjustable temperature – 50 to 250 ºC
• Heating surface:
• 65 x 135 mm – 1 zone
• 130 x 135 mm – 2 zones
• Type K TC connector – 4 for control and protection
• Profiles – 20 (up to 6 steps for each)
• Setting temperature profiles – 3 profiles (2, 3 or 4 steps)
• Maximum working time – 50 min or unlimited
• ESD Safe – Supports ANSI/ESD S20.20-2021
• USB-A – Update firmware, graphics and profiles
• USB-B – PC communications
• Robot connector – Remote control
• Aux. connector – Connection to the console
• Pedal connector – Pedal connection (P-005) for heater control

PHBE Preheater for printed circuit boards, dimensions 360x280mm

• Pedal connector – Pedal connection (P-005) for heater control
• Maximum power – 1800 W
• Adjustable temperature – 50 to 250 ºC
• Heating surface:
• 180 x 277 mm – 1 zone
• 360 x 277 mm -2 zones
• Type K TC connector – 4 for control and protection
• Profiles – 22 (up to 16 steps each)
• Setting temperature profiles – 3 profiles (2, 3 or 4 steps)
• Maximum working time – 50 min or unlimited
• ESD Safe – Supports ANSI/ESD S20.20-2021
• USB-A – Update firmware, graphics and profiles
• USB-B – PC communications
• Robot connector – Remote control
• Aux. connector – Connection to the console

PHXLE Preheater for printed circuit boards, dimensions 510x610mm

• Maximum power – 5400 W
• Adjustable temperature – 50 to 250 ºC / 120 to 482 ºF
• Heating surface:
  • 255 x 203 mm – 1 zone
  • 510 x 610 mm – 6 zones
• Type K TC connector – 8 for control and protection
• Profiles – 22 (up to 16 steps each)
• Adjust temperature profiles – 3 profiles (2,3 or 4 steps)
• Maximum working time – 50 min or unlimited
• ESD Safe – Supports ANSI/ESD S20.20-2021
• USB-A – Update firmware, graphics and profiles
• USB-B – PC communications
• Robot connector – Remote control
• Aux. connector – Connection to the console
• Pedal connector – Pedal connection (P-005) for heater control